AutoCAD® 2D for Geometric Design of Terbanggi Besar–Pematang Panggang Highway (Sta.28+650 – Sta.53+650)
DOI:
https://doi.org/10.53866/jimi.v2i5.189Keywords:
Highway Design, Horizontal Alignment, Road Geometric, Vertical AlignmentAbstract
With a length of approximately 2,818 kilometers, the Trans Sumatra Highway connects cities from Lampung to Aceh. Meticulous planning and adherence to the geometric and technical requirements of the route are required to provide good road service. The purpose of this paper is to specifically redesign the current route on the Terbanggi Besar-Pematang Panggang section of the highway. The information used in this report as a guide for re-planning came from the results of field surveys. The geometric design of this highway was carried out using the manual calculation method based on the Road Design Standards of Indonesia 2021 and visualized using AutoCAD® 2D. Based on available data, a design speed (VD) of 120 kph is determined according to the maximum value on flat terrain on the highway. As a result of data processing on a particular road section, a horizontal alignment with a full circle curve type with a radius of 1500 m was created. Meanwhile, a sag vertical curve type is obtained in the vertical alignment with a length value at one point of the curve (L) of 75.6 m
References
Abdulhafedh, A. (2019). Design of superelevation of highway curves: An overview and distribution methods. Journal of City and Development, 1(1), 35-40.
Andika, I., Rifai, A. I., Isradi, M., & Prasetijo, J. (2022). A Traffic Management System for Minimization of Intersection Traffic Congestion: Case Bengkong Junction, Batam. . IJEBD International Journal Of Entrepreneurship And Business Development eISSN 25, 57.
Ardiyono, S. K., Parenrengi, N. P., & Faturachman, F. (2018). How does toll road impact accessibilities, trades, and investments in short term? A case study of Cipali toll road in West Java, Indonesia. Journal of Infrastructure, Policy and Development, 226-247.
Chakole, H., & Wadhai, P. J. (2022). A Review on The comparison of geometric design using Civil 3D software and manual method. International Journal for Modern Trends in Science and Technology, 117.
Cigu, E., Agheorghiesei, D. T., Gavriluță, A. F., & Toader, E. (2018). Transport infrastructure development, public performance and long-run economic growth: a case study for the Eu-28 countries. Sustainability, 11(1), 67.
DGH. (2021). Hihgway Design Standar of Indonesia 2021. Jakarta: Directorate General of Highway, Ministry of Public Works & Housing.
Fakhurozi, A. N. (2020). Kajian Studi Dampak Pembangunan Jalan Tol Trans Sumatera (Jtts) Terhadap Infrastuktur Dan Lingkungan. Jurnal Ilmiah Penalaran dan Penelitian Mahasiswa, 4(1), 14-29.
Gaikawad, P., & Ghodmare, S. D. (2020). A Review-Geometric Design of Highway with the Help of Autocad Civil 3D. International Journal for Research in Applied Science and Engineering Technology, 8(5), 916.
Geedipally, S. R., Pratt, M. P., & Lord, D. (2019). Effects of geometry and pavement friction on horizontal curve crash frequency. Journal of Transportation Safety & Security, 11(2), 167-188.
Islam, M. H., Hua, L. T., Hamid, H., & Azarkerdar, A. (2019). Relationship of accident rates and road geometric design. In IOP Conference Series: Earth and Environmental Science.
Isradi, M., Prasetijo, J., Hartatik, I. N., Suryaningtyas, B., Dermawan, W., & Rifai, A. (2021). Analysis of Pavement Thickness Planning and Overlaying Method on Trans Sumatera Toll Road, Pekanbaru–Dumai. International Conference on Industrial Engineering and Operations Management, (p. 4161). Monterrey, Mexico: IEOM Society International.
Mandal, M., Pawade, P., & Sandel, P. (2019). Geometric design of highway using Civil 3D. International Journal of Advance Research, Ideas and Innovations in Technology, 5(3).
Mandal, N., Reddy, B. S., Vardhan, L. V., Taridala, I. S., Yudono, A., & & Ramli, M. I. (2017). Geometric and Road Environmental Effects against Total Number of Traffic Accidents in Kendari. Journal of Physics : Conference Series, 2.
Onur, A. Z., & Nouban, F. (2019). Software in the architectural presentation and design of buildings: State-of-the-art. International Journal of Innovative Technology and Exploring Engineering (IJITEE)[Online], 8(10).
Ozkan, E., Tuydes-Yaman, H., & Acar, S. O. (2021). Vertical alignment optimisation in highway design by means of mesh adaptive direct search. In Proceedings of the Institution of Civil Engineers-Transport (pp. 1-12). (p. 1). Thomas Telford Ltd.
Palm, B. S. (2020). Introduction to AutoCAD 2020: 2D and 3D design. Routledge.
Prasetyo, H., Widyastuti, H., & Kartika, A. A. (2020). Perencanaan Geometrik dan Perkerasan Jalan Tol kertosono-Kediri (Kertosono STA 0+ 000 sampai Kediri STA 21+ 300. Jurnal Teknik ITS, E51-E57.
Raji, S. A., Zava, A., Jirgba, K., & Osunkunle, A. B. (2017). Geometric Design of a Highway Using Autocad Civil 3d. Journal of Multidisciplinary Engineering Science and Technology (JMEST), 7415.
Rifai, A. I., Hadiwardoyo, S. P., Correia, A. G., & Pereira, P. A. (2016). Genetic Algorithm Applied for Optimization of Pavement Maintenance under Overload Traffic: Case Study Indonesia National Highway. Applied Mechanics and Materials (Vol. 845), pp. 36.
Rifai, A. I., Hadiwardoyo, S. P., Correia, A. G., Pereira, P., & Cortez, P. (2015). The data mining applied for the prediction of highway roughness due to overloaded trucks. International Journal of Technology, 6(5), 751-761.
Rifai, A. I., Surgiarti, A. Y., Isradi, M., & Mufhidin, A. (2022). Analysis of Road Performance and the impact of Development in Pasar Minggu, Jakarta : Case Study of Jalan Lenteng Agung-Tanjung Barat. ADRI International Journal of Civil Engineering, 68-74.
Rifai, A. I., & Hafis, K. (2020, May). Analysis of Road Performance and Vehicle Parking Characteristics in the Halim Perdanakusuma International Airport Area. In Journal of World Conference (JWC) (Vol. 3, No. 1, pp. 89-98).
Rifai, A.I., Wibowo, T., Isradi, M., & Mufhidin, A. (2021) On-Street Parking and Its Impact on Road Performance: Case Commercial Area in Jakarta City. World Journal of Civil Engineering Vol. 1 No. 1, pp. 10-18
Sasongko, R. (2018). Survey Rekayasa Konstruksi (Vol. 1). In R. Sasongko, Survey Rekayasa Konstruksi (pp. 1-9). Malang: UPT Percetakan dan Penerbitan Polinema.
Siswoyo, M. (2020). The Impact of Toll Road Development: An Analysis Based on Public Administration Ecology. Journal of Southwest Jiaotong University, 3.
Siswoyo, M. (2020). The Impact of Toll Roads Development: Ecology of Public Administration Perspective. Systematic Reviews in Pharmacy, 152-157.
Sukirman, S. (1999). Dasar-dasar Perencanaan Geometrik Jalan. Bandung: Nova.
Veer, S. P., Gupte, S., & Juremalani, J. (2018). A Review of Literature on Geometric Design of Highway. International Research Journal of Engineering and Technology (IRJET) Volume, 5.
Wang, X., & Wang, X. (2018). Speed change behavior on combined horizontal and vertical curves: driving simulator-based analysis. Accident Analysis & Prevention, 119, 215-224.
You, K., Yu, Q., Huang, W., & Hu, Y. (2022). Safety-Based Optimization Model for Highway Horizontal Alignment Design. Mathematical Problems in Engineering.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Ratih Yuliani Gunawan, Andri Irfan Rifai, Muhamad Alamsyah Irianto
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
